Xerox 4090 User Manual Page 121
- Page / 168
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SOLVING PROBLEMS
5. Press the Test switch. The diagnostic indicator illuminates,
and the display indicates 01.
6. Press the Execute switch. Test 01 starts with the display
panel stepping through the number pairs from 00, 11, 22, 33,
through 99. Make sure that these numbers appear correctly
and in sequence. Also, make sure that all indicators except
Logic Off, BOT, and High Density are lit.
Test 01 continues with various tape motion and read/write
exercises for approximately 10 minutes if a 10.5 inch reel
(2400 feet/731.5 meters) is used.
If the test runs to completion, it was successful. The transport
performs a rewind/unload operation. The digital display indicates
00 and the Reset indicator illuminates. This does not mean that
the problem is resolved, only that some of the possible causes
have been eliminated by the diagnostic program. When placing
the service call, make sure to indicate whether or not Diagnostic
Test 01 was successful.
If the test does not run to completion when it stops and a
numerical fault code appears in the display window, refer to the
operator-correctable actions list inside the door of the tape drive
unit (lower half of the list) and follow those directions. Reinitiate
Test 01 to see if it can run to completion. If not, report any and
all numbers when placing the service call.
Additional diagnostic tests
Your service representative may ask you to perform the
additional diagnostic tests 02 and 03.
Diagnostic Test 02
In some cases, your service representative may ask you to
perform Diagnostic Test 02 to check tape tension. Never
attempt to perform this test, except when directed to do so by a
service representative.
Follow these steps if directed to perform Diagnostic Test 02:
1. Make sure that the transport is powered on. Thread a
scratch tape but do not load it. Close and latch the door.
2. First press the Reset switch, then the test switch. The
diagnostics indicator should be lit, and 01 should appear in
the display window.
3. Press the Step switch one time. The numerical display steps
from 01 to 02. If you press it too many times, press the
Reset switch and repeat this step.
4. Press the Execute switch. Test 02 starts and runs for less
than 30 seconds.
If 00 displays at the completion of the test, it was successful. If
the test was unsuccessful, the diagnostic program halts, the Reset
indicator lights, and a numerical fault code appears on the
display. Record this number and report it when placing the
service call.
XEROX 4050/4090/4450/4650 LPS OPERATOR GUIDE 8-3
- Xerox 4050/4090/4450/4650 1
- Laser Printing Systems 1
- Operator Guide 1
- Laser safety 3
- Operational safety 3
- Ozone information 4
- Radio communication 4
- Table of contents 5
- 4. Printing jobs 4-1 6
- 6. Printer maintenance 6-1 7
- 5. Print job maintenance 5-1 7
- 7. Shutting down the LPS 7-1 8
- 8. Solving problems 8-1 8
- Appendices 8
- Glossary GLOSSARY-1 9
- Index INDEX-1 9
- Introduction 11
- Related publications 12
- Printing color jobs 13
- 1. Overview 15
- LPS features 16
- 4050 LPS 17
- 4090 LPS 17
- 4650 LPS 17
- 4450 LPS 17
- System components 18
- Optional components 19
- OVERVIEW 20
- System controller options 21
- Print job sources 23
- Basic system functions 24
- Commands 25
- 2. Setting up the LPS 27
- 9-track magnetic tapes 29
- 18-track cartridge tapes 30
- SETTING UP PRINT JOB SOURCES 31
- Control panel switches 34
- Powering on the tape drive 37
- Loading a 9-track tape 37
- Unloading a tape 40
- Powering off the tape drive 40
- Locating CTS components 42
- Powering on the 180 CTS 45
- Loading a tape 45
- Receiving offline jobs 48
- Placing the LPS online 49
- Taking the LPS offline 49
- Starting HIP 50
- Changing hosts 51
- Placing HIP online 51
- Taking HIP offline 52
- 4. Printing jobs 53
- Setting up feeder trays 54
- Setting up output trays 54
- Printing samples 55
- Starting a print job 56
- PRINTING JOBS 57
- Checking printer status 59
- Checking job status 62
- Managing print jobs 63
- Ending a print job 64
- Interrupting a print job 64
- Stopping a HIP print job 65
- 5. Print job maintenance 67
- PRINT JOB MAINTENANCE 68
- Adding stitcher wire 69
- Adjusting form alignment 69
- Changing paper size 72
- Loading feeder trays 72
- Selecting feeder trays 76
- Displaying cluster status 78
- Setting current trays 79
- Modifying current trays 80
- Error conditions 81
- Using the FEED command 82
- Selecting output trays 83
- Unloading output trays 85
- Unloading the sample tray 86
- <CON> on the keyboard 87
- 6. Printer maintenance 89
- Cleaning the diskette drive 98
- Cleaning exterior surfaces 99
- Copying and backing up files 99
- PRINTER MAINTENANCE 100
- Handling diskettes 103
- Formatting a diskette 104
- 14. Install the new wiper 110
- Setting the time and date 112
- Time and status display 113
- A T T N 114
- 7. Shutting down the LPS 117
- SHUTTING DOWN THE LPS 118
- 8. Solving problems 119
- SOLVING PROBLEMS 120
- Additional diagnostic tests 121
- Paper jams 122
- ENTER CON O 123
- PRINTER JAM IN AREA see IOT 123
- Clearing area 1A 124
- Clearing area 2A 125
- Clearing areas 3 through 5 125
- Clearing areas 6 and 6A 128
- Clearing area 7 129
- Clearing areas 8 and 9 130
- Clearing areas A and B 131
- Paper misfeeds 133
- Frequent paper misfeeds 134
- Stitcher/stacker problems 136
- Blank display 138
- Rasterization messages 138
- System rollover 139
- Power loss 140
- Calling for service 141
- A. Paper 145
- Paper storage 146
- Paper conditioning 147
- Paper curl 148
- Meter reading 149
- METER READING AND REPORTING 151
- Glossary 157
- GLOSSARY 158
Related products and manuals for Printers Xerox 4090
Printers Xerox 2006CP User Manual
(2 pages)
(2 pages)
Printers Xerox DOCUCOLOR 12 User Manual
(2 pages)
(2 pages)
Printers Xerox 6350 User Manual
(4 pages)
(4 pages)
Printers Xerox 5050 User Manual
(4 pages)
(4 pages)
Printers Xerox DocuColor 2045 User Manual
(144 pages)
(144 pages)
Printers Xerox 8264E EN User Manual
(30 pages)
(30 pages)
Printers Xerox PE220 User Manual
(200 pages)
(200 pages)
Printers Xerox 6128MFP User Manual
(3 pages)
(3 pages)
Printers Xerox 721P85600 User Manual
(116 pages)
(116 pages)
Printers Xerox Phaser 7300 User Manual
(28 pages)
(28 pages)
Printers Xerox Phaser 7750 User Manual
(5 pages)
(5 pages)
Printers Xerox Phaser 6100 User Manual
(7 pages)
(7 pages)
Printers Xerox TM 4500 User Manual
(3 pages)
(3 pages)
Printers Xerox 92C NPS User Manual
(64 pages)
(64 pages)
Printers Xerox Phaser 3435 User Manual
(98 pages)
(98 pages)
Printers Xerox 4150 User Manual
(1 pages)
(1 pages)
Printers Xerox 2218 User Manual
(11 pages)
(11 pages)
Printers Xerox 212 DC User Manual
(2 pages)
(2 pages)
JVC HRDVS1EK podręczniki
Instrukcje obsługi i podręczniki użytkownika dla odtwarzacze CD JVC HRDVS1EK.
Dostarczamy pdf podręczników JVC HRDVS1EK do pobrania za darmo według typów dokumentów:
Comments to this Manuals