Xerox 4090 User Manual Page 120
- Page / 168
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SOLVING PROBLEMS
Diagnostic Test 01
The built-in Diagnostic Test 01 is used to verify a malfunction
when a fault code indicates transport failure. Test 01 should be
performed prior to calling for service because the information
obtained assists the service representative. As soon as a problem
becomes evident through fault code messages, record or log all
fault messages so that the service representative can determine
not only the type of malfunction but also the circumstances
under which the fault occurred.
Follow these steps to perform Diagnostic Test 01:
1. Press the Power switch off and then on. This causes the tape
drive to perform a diagnostic self-check. If a fault is
indicated at this time, do not attempt further testing. Place a
service call.
2. Thread a scratch tape through the tape path and onto the
take-up reel but do not load it.
Note: A scratch tape is a tape of known good quality that
has no needed data written on it. It must have a write-
enable ring installed because Test 01 performs the read/write
function during its operation.
CAUTION: The use of anything other than a scratch tape
while performing any diagnostic test could result in severe
data loss. Always install a scratch tape of known good quality
before performing any diagnostic tests.
3. Close and latch the door.
4. Press the Reset switch.
8-2 XEROX 4050/4090/4450/4650 LPS OPERATOR GUIDE
- Xerox 4050/4090/4450/4650 1
- Laser Printing Systems 1
- Operator Guide 1
- Laser safety 3
- Operational safety 3
- Ozone information 4
- Radio communication 4
- Table of contents 5
- 4. Printing jobs 4-1 6
- 6. Printer maintenance 6-1 7
- 5. Print job maintenance 5-1 7
- 7. Shutting down the LPS 7-1 8
- 8. Solving problems 8-1 8
- Appendices 8
- Glossary GLOSSARY-1 9
- Index INDEX-1 9
- Introduction 11
- Related publications 12
- Printing color jobs 13
- 1. Overview 15
- LPS features 16
- 4050 LPS 17
- 4090 LPS 17
- 4650 LPS 17
- 4450 LPS 17
- System components 18
- Optional components 19
- OVERVIEW 20
- System controller options 21
- Print job sources 23
- Basic system functions 24
- Commands 25
- 2. Setting up the LPS 27
- 9-track magnetic tapes 29
- 18-track cartridge tapes 30
- SETTING UP PRINT JOB SOURCES 31
- Control panel switches 34
- Powering on the tape drive 37
- Loading a 9-track tape 37
- Unloading a tape 40
- Powering off the tape drive 40
- Locating CTS components 42
- Powering on the 180 CTS 45
- Loading a tape 45
- Receiving offline jobs 48
- Placing the LPS online 49
- Taking the LPS offline 49
- Starting HIP 50
- Changing hosts 51
- Placing HIP online 51
- Taking HIP offline 52
- 4. Printing jobs 53
- Setting up feeder trays 54
- Setting up output trays 54
- Printing samples 55
- Starting a print job 56
- PRINTING JOBS 57
- Checking printer status 59
- Checking job status 62
- Managing print jobs 63
- Ending a print job 64
- Interrupting a print job 64
- Stopping a HIP print job 65
- 5. Print job maintenance 67
- PRINT JOB MAINTENANCE 68
- Adding stitcher wire 69
- Adjusting form alignment 69
- Changing paper size 72
- Loading feeder trays 72
- Selecting feeder trays 76
- Displaying cluster status 78
- Setting current trays 79
- Modifying current trays 80
- Error conditions 81
- Using the FEED command 82
- Selecting output trays 83
- Unloading output trays 85
- Unloading the sample tray 86
- <CON> on the keyboard 87
- 6. Printer maintenance 89
- Cleaning the diskette drive 98
- Cleaning exterior surfaces 99
- Copying and backing up files 99
- PRINTER MAINTENANCE 100
- Handling diskettes 103
- Formatting a diskette 104
- 14. Install the new wiper 110
- Setting the time and date 112
- Time and status display 113
- A T T N 114
- 7. Shutting down the LPS 117
- SHUTTING DOWN THE LPS 118
- 8. Solving problems 119
- SOLVING PROBLEMS 120
- Additional diagnostic tests 121
- Paper jams 122
- ENTER CON O 123
- PRINTER JAM IN AREA see IOT 123
- Clearing area 1A 124
- Clearing area 2A 125
- Clearing areas 3 through 5 125
- Clearing areas 6 and 6A 128
- Clearing area 7 129
- Clearing areas 8 and 9 130
- Clearing areas A and B 131
- Paper misfeeds 133
- Frequent paper misfeeds 134
- Stitcher/stacker problems 136
- Blank display 138
- Rasterization messages 138
- System rollover 139
- Power loss 140
- Calling for service 141
- A. Paper 145
- Paper storage 146
- Paper conditioning 147
- Paper curl 148
- Meter reading 149
- METER READING AND REPORTING 151
- Glossary 157
- GLOSSARY 158
Related products and manuals for Printers Xerox 4090
Printers Xerox 2006CP User Manual
(2 pages)
(2 pages)
Printers Xerox DOCUCOLOR 12 User Manual
(2 pages)
(2 pages)
Printers Xerox 6350 User Manual
(4 pages)
(4 pages)
Printers Xerox 5050 User Manual
(4 pages)
(4 pages)
Printers Xerox DocuColor 2045 User Manual
(144 pages)
(144 pages)
Printers Xerox 8264E EN User Manual
(30 pages)
(30 pages)
Printers Xerox PE220 User Manual
(200 pages)
(200 pages)
Printers Xerox 6128MFP User Manual
(3 pages)
(3 pages)
Printers Xerox 721P85600 User Manual
(116 pages)
(116 pages)
Printers Xerox Phaser 7300 User Manual
(28 pages)
(28 pages)
Printers Xerox Phaser 7750 User Manual
(5 pages)
(5 pages)
Printers Xerox Phaser 6100 User Manual
(7 pages)
(7 pages)
Printers Xerox TM 4500 User Manual
(3 pages)
(3 pages)
Printers Xerox 92C NPS User Manual
(64 pages)
(64 pages)
Printers Xerox Phaser 3435 User Manual
(98 pages)
(98 pages)
Printers Xerox 4150 User Manual
(1 pages)
(1 pages)
Printers Xerox 2218 User Manual
(11 pages)
(11 pages)
Printers Xerox 212 DC User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 1.830 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals